Catalog excerpts
MOUNTED BEARING UNITS MOUNTED BEARING UNITS NIPPON PILLOW BLOCK CO., LTD.
NIPPON PILLOW BLOCK CO., LTD. HEAD OFFICE 2306 Hirao Mihara-ku Sakai Osaka 587-0022 Japan TEL: +81-72-361-3750 FAX: +81-72-361-4173 www.fyhbearings.com E-mail: info@fyhbearings.com INTERNATIONAL DIVISION E-mail: exports@fyh.co.jp FYH BEARING UNITS USA INC. 13201 FYH Drive Huntley, Illinois 60142, USA TEL: +1-847-487-9111 FAX: +1-847-487-9222 E-mail: sales@fyhusa.com DOMESTIC BRANCHES IN JAPAN Tokyo Nagoya Sapporo Fukuoka Hiroshima Kase Building 116-5 F 1-3-49 Katsushima Shinagawa Tokyo 140-0012 Japan TEL: +81-3-5767-7270 FAX: +81-3-5767-7280 E-mail:tokyo@fyh.co.jp 2-1-2 Niban Atsuta-ku...
Mounted Bearing Units (contents) Technical Section Technical Section Pillow Block Units Oval Flange Units 4-Bolt Flange Cartridge Units BALL BEARING UNITS Stamped Steel Flange Units Take-Up Units Cartridge Units Hanger Units Ball Bearing Inserts SPHERICAL ROLLER BEARING UNITS Technical Section Parts and Accessories Technical Section Spherical Roller Bearing Units Appendix Table Appendix Table
BALL BEARING UNITS Technical Section 1 Structure and Features 4 Rating Life of Bearings 4.1 Basic Rating Life and Basic Load Rating .. 33
Parts and Accessories 16 Parts and Accessories
SPHERICAL ROLLER BEARING UNITS Appendix Table The contents of this catalogue are subject to change without prior notice. Every possible effort has been made to ensure that the data listed in this catalog is correct. However, we can not assume responsibility for any errors or omissions. All rights reserved.
1 Structure and Features FYH Ball Bearing Units are manufactured to exacting standards comprising of grease sealed deep groove ball bearings and housings in various forms. Self-aligning units allow for easy installation and are supplied with grease fittings in order to facilitate quick and convenient re-lubrication. 1.1 Structure FYH Ball Bearing Units are constructed of high carbon chromium bearing steel and have precision honed raceways and riveted steel cages (Fig. 1.1). Grease fitting Outer ring with spherical outside surface Grease hole Double lip FloBack seal Ball and cage Wide inner...
3 Superior sealing performance FYH Ball Bearing Units efficiently prevent grease from leaking out of the interior of the bearing, and perform extremely well at keeping contaminates, such as dust and water, from entering. This is achieved by installing the seal to the outer ring of the bearing and installing the slinger to the inner ring of the bearing. The FloBack seal to be used in the standard FYH Ball Bearing units will contribute to the long life of the bearing. It consists of a double-lip seal which is stamped into place in the outer ring of the bearing to reduce the possibility of...
5 Highly rigid and rugged cast iron housings FYH Ball Bearing Unit housings are designed so that they are optimized for reduction of deformation due to centralization of stress and load. Only the best material is selected to be cast by a highly advanced technique or press working technique, depending on the housing. Since any abnormal load on the bearing is eliminated by the housing, the life of the bearing can be extended. A Granular material baking finish coating (powder coating) helps resist corrosion and protect the surface of the housing for an extended period of time. FYH original...
2 Selection Guide 2.1 Selection Guide 1. Select the housing style that best suits your application. P - PILLOW BLOCK PA - TAPPED-BASE PH - HIGH-BASE LP - LIGHT IP - THICK PP - STAMPED STEEL F - 4-BOLT FLANGE FS - SQUARE PILOTED FL - 2-BOLT FLANGE LF - LIGHT PFL - STAMPED STEEL FA - ADJUSTABLE FB - 3-BOLT FLANGE FC - 4-BOLT FLANGE CARTRIDGE T - TAKE-UP C - CARTRIDGE H - HANGER 2. Select the shaft size and duty that is needed for your application. SU - FROM 10 MM TO 30 MM BORE SA & SB - FROM 12 MM & 1/2” TO 40 MM & 1-9/16” BORE UC - FROM 12 MM & 1/2” TO 140 MM BORE NA - FROM 12 MM & 1/2” TO...
3. Do you need to customize the bearing for your application? Select STANDARD as the default. TEMP - D2K2 -58°F TO 248°F (-50°C TO 120°C), D1K2 -40°F TO 356°F (-40°C TO 180°C), D9K2 -4°F TO 446°F (-20°C TO 230°C) WASH DOWN - STAINLESS STEEL UNITS, PLASTIC HOUSING UNITS, AIR HANDLING - S3 AIR HANDLING FIT UNITS, S5 NON CONTACT SEAL DUST - L3 TRIPLE LIP SEAL, COVERS DIRT - LT3 TIGHT TRIPLE LIP SEAL, COVERS 4. Select the locking style type for your insert. UC - SETSCREW LOCK NA - ECCENTRIC COLLAR LOCK NC - CONCENTRIC COLLAR LOCK UK - ADAPTER SLEEVE LOCK Selection application is available for...
2.2 High / Low Temperature Series (suffix codes - High temperature: D1K2 & D9K2, Low temperature: D2K2) For applications that require bearing units to be used at a higher or lower temperature range than our standard models FYH offers several options. For high temperature units that require lubrication please specify D1K2 as a suffix to the standard part number. For high temperature units that do not require lubrication specify D9K2. The D9K2 insert uses a fluoro-grease that allows for excellent heat resistance and operation with minimal maintenance. Specifications for the high temperature...
2.2.1 Rotational speed adjustment due to shaft fit A marginal degree of clearance is typically used to facilitate easy installation of a bearing to a shaft. The amount of clearance between the bearing and shaft must be factored in to determine the maximum allowable rotational speed, and as rotational speed is increased, the amount of clearance must be decreased. Table 2.3 shows the factor that must be used to correct the allowable rotational speed. The maximum rotational speed is determined by multiplying the speed found in Table 6.1 by the factors below. Table 2.3 Fitting factor of ball...
WASH DOWN 2.3 Corrosion Resistant Series The Corrosion Resistant Series is available in a wide array of sizes and styles, and units may be customized with a number of different specialized options to accommodate virtually any application. Federal compliance can be assured with FYH Bearing Units. S6 STAINLESS INSERT RINGS BALLS CAGE GREASE SEALS SLINGER ANTI-ROTATION PIN SET SCREWS AVAILABLE SIZES CLEARANCE S7 PLATED INSERT RINGS BALLS CAGE GREASE SEALS SLINGER ANTI-ROTATION PIN SET SCREWS AVAILABLE SIZES CLEARANCE SUJ2 + (zinc plated + trivalent chromate treatment) SUJ2 NYLON H1 FOOD GRADE...